航天推进技术研究院主办
[1]王晨威,闫方琦,李智军,等.考虑法兰变形的U-E金属密封结构匹配优化设计[J].火箭推进,2023,49(03):115-122.
WANG Chenwei,YAN Fangqi,LI Zhijun,et al.Matching optimization design of U-E metal seal structure considering flange deformation[J].Journal of Rocket Propulsion,2023,49(03):115-122.
点击复制
WANG Chenwei,YAN Fangqi,LI Zhijun,et al.Matching optimization design of U-E metal seal structure considering flange deformation[J].Journal of Rocket Propulsion,2023,49(03):115-122.
考虑法兰变形的U-E金属密封结构匹配优化设计
《火箭推进》[ISSN:1672-9374/CN:CN 61-1436/V]
卷:
49
期数:
2023年03期
页码:
115-122
栏目:
目次
出版日期:
2023-06-25
- Title:
- Matching optimization design of U-E metal seal structure considering flange deformation
- 文章编号:
- 1672-9374(2023)03-0115-08
- 分类号:
- V261.34
- 文献标志码:
- A
- 摘要:
- 针对液体火箭发动机大直径高温高压轻量化法兰变形量大导致密封泄漏的问题,采用Walters法结合三维仿真实验对法兰变形进行分析,阐明了法兰变形量及U-E金属主/副密封面密封比压变化,通过法兰变形量对U-E主/副密封之间的高度进行匹配设计; 对于U-E密封复杂横截面多结构参数,设计正交实验,结合法兰变形量,系统开展了U-E金属主/副密封设计。结果表明:法兰变形导致压缩量减小,密封回弹量增大,可导致U-E结构的密封比压不足; 通过增加压缩量,增加U-E主/副密封高度差,U-E密封正交试验的结构优化,有效地解决了法兰变形下的密封比压不足问题。对优化后的结构进行重复充泄压试验,试验结果均满足要求。
- Abstract:
- Aiming at the seal leakage problem of liquid rocket engine caused by large diameter flange deflection, high temperature and high pressure, the flange deformation was analyzed and the specific-pressure of the U-E metal seal was illustrated by employing the Walters method and virtual simulation experiment. Further, the match of main and secondary height of U-E seal was designed. On this basis, the cross-section of U-E seal was optimized by orthogonal experiment with the obtained flange deformation. The results show that the seal reduction decreases and the springback increases caused by flange deflection; the specific-pressure of present U-E seal is not appropriate and is improved with the method of both increasing seal compression and the height difference of the main and secondary seal, as well as implementing the structure optimization of seal by orthogonal experiment. The optimized structure is tested and validated.
参考文献/References:
[1] 杜天恩.高压液体火箭发动机新结构密封[J].推进技术,2000,21(4):16-19.
[2] SHEN M X,PENG X D,XIE L J,et al.Deformation characteristics and sealing performance of metallic O-rings for a reactor pressure vessel[J].Nuclear Engineering and Technology,2016,48(2):533-544.
[3] YUDHOWIJOYO A,RAFATI R,SHARIFI HADDAD A,et al.Subsurface methane leakage in unconventional shale gas reservoirs:A review of leakage pathways and current sealing techniques[J].Journal of Natural Gas Science and Engineering,2018,54:309-319.
[4] FINKBEINER J R,DUNLAPP H,STEINETZ B M,et al.Review of seal designs on the Apollo spacecraft[J].Journal of Spacecraft and Rockets,2008,45(5):900-910.
[5] Parker Hannifin Corporation.Metal seal design guide-high performance engineered seals and sealing systems[Z].2011.
[6] FLITNEY R.Seals and sealing handbook [Z].6th ed.[S.l.]:Butterworth-Heinemann Publication,2014.
[7] LIU Y,ZHOU K,HUANG W F,et al.Numerical and experimental analysis of the reusability of spring energized metal C rings[J].Science China Technological Sciences,2014,57(8):1670-1676.
[8] GORBACHEV A,GROMYKO B,MATVEEV E,et al.Detachable fixed sealing device:1499031A1[P].1989.
[9] LEFRAN?OIS M.Metal-to-metal seals[J].Sealing Technology,2004,2004(4):10-13.
[10] 马莹,王良.U-E密封设计研究[J].火箭推进,2015,41(3):66-72.
MA Y,WANG L.Design research of U-E-type metal sealing[J].Journal of Rocket Propulsion,2015,41(3):66-72.
[11] 杜宸宇,孙丹,赵磊,等.异形结构弹性金属密封环力学特性数值研究[J].润滑与密封,2021,46(7):114-120.
[12] 薛杰,黄金平.工作压力下法兰结构螺栓及密封件受力特性[J].火箭推进,2021,47(5):65-70.
XUE J,HUANG J P.Force characteristics of frange structure bolts and seals under working pressure[J].Journal of Rocket Propulsion,2021,47(5):65-70.
[13] NASH D H,SPENCE J,TOOTH A S,et al.A parametric study of metal-to-metal full face taper-hub flanges[J].International Journal of Pressure Vessels and Piping,2000,77(13):791-797.
[14] LIN T J,LI R F,LONG H,et al.Three-dimensional transient sealing analysis of the bolted flange connections of reactor pressure vessel[J].Nuclear Engineering and Design,2006,236(24):2599-2607.
[15] YU S Y,LIU J J,ZUO W D,et al.Sealing behavior of the HTR-10 pressure vessel flanges[J].Nuclear Engineering and Design,2002,216(1/2/3):247-253.
[16] ASME.ASME boiler and pressure vessel code[EB/OL].https://files.asme.org/Catalog/Codes/PrintBook/13884.pdf,2007.
[17] 刘延柱,薛纭.关于弹性梁的数学模型[J].力学与实践,2011,33(1):74-78.
[18] MICHEL D,PAYNE J R.New PVRC constants for gasket selection and new ASME rules for bolted flanged joints[Z].1997.
[19] 刘兴,赖华,屈景年,等.关于Clapeyron方程推导的探讨[J].山东化工,2017,46(16):171.
[20] PHILLIPS D R,WINGATA R J.Seal joint analysis and design for the Ares-I upper stage LOX tank[EB/OL].https://www.researchgate.net/publication/271375665_Seal_Joint_Analysis_and_Design_for_the_Ares-I_Upper_Stage_LOX_Tank,2011.
[21] 张贵田.高压补燃液氧煤油发动机[M].北京:国防工业出版社,2005.
备注/Memo
收稿日期:2022-06-28; 修回日期:2022-09-03
基金项目:国家自然科学基金项目(11702204)
作者简介:王晨威(1998—),男,硕士,助理工程师,研究领域为金属密封。
更新日期/Last Update:
1900-01-01