航天推进技术研究院主办
LIU Xing-bin,YE Hui,ZHAI Hui-feng.Research on plating process of heat exchanger[J].Journal of Rocket Propulsion,2011,37(03):42-47.
换热器镀层工艺研究
- Title:
- Research on plating process of heat exchanger
- 文章编号:
- 1672-9374(2011)03-0042-06
- Keywords:
- heat exchanger; solderability; oxidation resistance
- 分类号:
- TG174
- 文献标志码:
- A
- 摘要:
- 通过理论分析和工艺试验等方式,探索了由性能差异较大的不同材料组成的换热器选择性电镀工艺方法。采用局部遮蔽、浸蚀溶液的选择、预镀工艺的确定等方式,保证了组合件上各型面、各材料上的镀层质量,换热器上局部镀覆层既满足钎焊性,同时又满足高温抗氧化性的功能要求,并顺利完成了钎焊和热试车。本研究成果已在多个结构复杂的换热器上得到推广应用。
- Abstract:
- Based on theoretic analysis and process tests, the selective plating process of a heat exchanger made of different materials with large performance difference is investigated. The coating quality on different profiles and materials of the heat exchanger assembly is guaranteed by partial sheltering, etching solution selection and pre-plating process. The function requirements of solderability and high temperature oxidation resistance on each local coating of heat exchanger are satisfied. Therefore, the subsequent brazing and hot firing were successfully achieved. The plating process mentioned above has been applied to several heat exchangers with complex structure.
参考文献/References:
[1]曾华梁. 电镀工艺手册[M]. 北京: 机械工业出版社, 1996.
[2]张允诚, 胡如南. 电镀手册[M]. 2版. 北京: 国防工业出版社, 2001.
[3]张贵田. 高压补燃液氧煤油发动机[M]. 北京: 国防工业出版社, 2005.
[4]冯绍斌. 电镀清洁生产工艺[M]. 北京: 化学工业出版社, 2005.
[5]李异. 金属表面清洗技术[M]. 北京: 化学工业出版社, 2007.
[6]张康夫, 萧怀斌, 罗永秀. 防锈材料应用手册[M]. 北京: 化学工业出版社, 2004.
[7]刘道新 主编. 材料的腐蚀与防护[M]. 西安: 西北工业大学出版社, 2006.
[8]刘振海, 富山立子. 分析化学手册第八分册热分析[M]. 北京: 化学工业出版社, 2000.
[9]郭会民, 赵仕哲, 李万万. 溶化极混合气体保护焊工艺研究与应用[J]. 火箭推进, 2007, 33(2):57-62.
[10]韩冬, 杨合, 张立武, 等. 旋3A21铝合金热处理及旋压温度其组织性能的影响[J]. 固体火箭技术, 2010, 33(2):225-228.
备注/Memo
收稿日期:2010-11-03;修回日期:2010-12-06
基金项目:国家航天技术支撑项目
作者简介: 刘兴斌(1974—),男,高级工程师,研究领域为表面处理应用