航天推进技术研究院主办
[1]仵亮,赵飞,徐鸿翔,等.四刃交汇切刀的磨削工艺研究[J].火箭推进,2017,43(02):82-86.
WU Liang,ZHAO Fei,XU Hongxiang,et al.Research on grinding technology of four-blade interactive cutter[J].Journal of Rocket Propulsion,2017,43(02):82-86.
点击复制
WU Liang,ZHAO Fei,XU Hongxiang,et al.Research on grinding technology of four-blade interactive cutter[J].Journal of Rocket Propulsion,2017,43(02):82-86.
四刃交汇切刀的磨削工艺研究
《火箭推进》[ISSN:1672-9374/CN:CN 61-1436/V]
卷:
43
期数:
2017年02期
页码:
82-86
栏目:
工艺与材料
出版日期:
2017-06-01
- Title:
- Research on grinding technology of four-blade interactive cutter
- Keywords:
- cutter; grinding technology; pyro-valve
- 分类号:
- V261.2-34
- 摘要:
- 针对电爆阀切刀的结构特点及质量要求,在分析切刀磨削难点的基础上,对切刀磨削方案,磨削过程控制及磨削注意事项进行了全面分析,得出了最佳的切刀磨削工艺方法.采用该磨削工艺方法进行切刀磨削试验和切刀切破膜片试验,试验结果均满足设计要求,证明了此磨削工艺能够生产出合格的四刃交汇切刀.
- Abstract:
- According to the structure features and quality requirements ofthe cutter for pyro-valve,the grinding scheme,control and cautions in the grinding process of the cutter was analyzed comprehensively based on the analysis of grinding difficulty,the best grinding technique of the cutter was obtained.The experiments of the grinding technique and the membrane cutting of the four-blade interactive cutter were done.The experimental results indicate that the grinding technique can meet the design requirements,and can produce the qualified four-blade interactive cutter.
参考文献/References:
[1]朱宁昌. 液体火箭发动机设计[M]. 北京: 宇航出版社, 1994．
[2]尤裕荣, 杜大华, 袁洪滨, 等. 电爆阀起动过程的响应特性与活塞撞击变形分析[J]. 火箭推进, 2012, 38(3): 49- 53．
YOU Yu-rong, DU Da-hua, YUAN Hong-bin, et al. Analyses of response characteristics and piston impact deformation in process of pyro-valve start-up. Journal of rocket propulsion, 2012, 38(3): 49-53．
[3]任敬心, 康仁科, 王西彬. 难加工材料磨削技术[M]. 北京: 电子工业出版社, 2011．
[4]任敬心, 华定安. 磨削原理[M]. 北京: 电子工业出版社, 2011．
[5]李波, 刘赫. 钎焊式离心轮加工工艺研究[J]. 火箭推进, 2011, 37(6): 46-51．
LI Bo, LIU He. Technological research on machining of brazed centrifugal impeller[J]. Journal of rocket propulsion, 2011, 37(6): 46-51.
[6]赵永强, 侯红玲, 李志峰, 周斌, 田广利. 双螺杆压缩机转子的精密磨削工艺研究[J]. 制造技术与机床, 2014, (2): 28-32．
[7]黄新春, 张定华, 姚倡锋, 等. 磨削参数对GH4169高温合金磨削表面特征影响研究[J]. 中国机械工程, 2014, 25(2): 210-214．
[8]任敬心, 康仁科, 王西彬. 难加工材料磨削技术[M]. 北京: 电子工业出版社, 2011．
[9]刘林枝. SUS304 不锈钢 ELID 镜面磨削正交化实验研究[J]. 机械科学与技术, 2013, 32(4): 506-509.
[10]杨春强, 黄云, 黄智, 等. 1Cr13不锈钢砂带磨削试验研究[J]. 机械科学与技术, 2011, 30(6): 1007-1010.
备注/Memo
收稿日期：2015-11-12；修回日期：2016-05-07 作者简介：仵亮（1988—），男，工程师，研究领域为液体火箭发动机阀门制造
更新日期/Last Update:
1900-01-01