PDF下载 分享
[1]王振,谭永华,黄道琼,等.液体火箭发动机离心轮极限转速分析与试验[J].火箭推进,2017,43(05):45-51.
　WANG Zhen,TAN Yonghua,HUANG Daoqiong,et al.Analysis and test for limit speed of centrifugal impeller in liquid rocket engine[J].Journal of Rocket Propulsion,2017,43(05):45-51.
点击复制

液体火箭发动机离心轮极限转速分析与试验

《火箭推进》[ISSN:1672-9374/CN:CN 61-1436/V] 卷: 43 期数: 2017年05期 页码: 45-51 栏目: 研究与设计 出版日期: 2017-10-15
Title:
Analysis and test for limit speed of centrifugal impeller in liquid rocket engine
作者:
王振1; 谭永华2; 黄道琼1; 宣统1
1.液体火箭发动机技术重点实验室,陕西 西安 710100; 2.航天推进技术研究院,陕西 西安 710100
Author(s):
WANG Zhen1; TAN Yonghua2; HUANG Daoqiong1; XUAN Tong1
1.Science and Technology on Liquid Rocket Engine Laboratory, Xi'an 710100,China; 2.Academy of Aerospace Propulsion Technology,Xi'an 710100,China
关键词:
液体火箭发动机;  离心轮;  极限转速;  最大正等效应力法;  双切线法;  超速试验
Keywords:
liquid rocket engine;  centrifugal pump impeller;  limit rotation speed;  maximum positive equivalence stress method;  double tangent intersection method;  overspeed spin test
分类号:
V415.1-34
文献标志码:
A
摘要:
为确保液体火箭发动机离心泵叶轮(离心轮)安全可靠工作,提出了基于强度的最大“正”等效应力法和基于刚度的双切线法两种失效判别准则以进行离心轮极限转速分析,并开展了离心轮超速试验进行验证。结果表明:最大“正”等效应力法准确地预测了离心轮破裂起始位置和破坏形式,误差低于15%; 双切线法预测的屈服转速与试验结果符合较好,误差低于5%。对于塑性较好的离心轮结构,采用屈服转速替代破裂转速进行极限转速设计分析更利于实现低成本、高可靠性的设计目标。
Abstract:
In order to guarantee the safety and reliability of centrifugal impeller in the liquid rocket engine(LRE),two failure criterions,that is the maximum positive equivalence stress method for strength and the double tangent intersection method for stiffness,are proposed to compute the limit rotation speed of centrifugal pump impeller in LRE.The corresponding overspeed spin tests were conducted to verify and compare the above two failure criterions.The results show that the maximum positive equivalence method can correctly predict the initial position and form of the failure,whose relative error is less than 15%,and the double tangent intersection method has predicted the closest results compared to that of the spin testing,whose relative error is less than 5%.For the centrifugal impellers with high plasticity,the yield speed is selected instead of the burst speed for the limit speed design and analysis,which is more helpful for realization of the low cost and high reliability of design goals.

参考文献/References:

[1] HUZEL D K, HUANG D H. Modern engineering for design of liquid-propellant rocket engines [M]. USA: AIAA, 1992.
[2] 陈晖, 张恩昭, 谭永华, 等. 高速平板诱导轮的结构设计与分析[J]. 火箭推进, 2009, 35(3): 1-5.
CHEN Hui, ZHANG Enzhao, TAN Yonghua,.et al. Geometry design and analysis of the high-speedrotational plate inducer [J]. Journal of rocket propulsion, 2009, 35(3): 1-5.
[3] NASA. Strength and life assessment requirements for liquid fueled space propulsion system engines: NASA-STD-5012 [S]. USA: NASA, 2006, 6.
[4] BERNSTEIN K S. Structural design requirements and factors of safety for spaceflight hardware for human spaceflight [S]. USA: NASA Johnson Space Center, 2011, 10.
[5] GUICHARD D, LAITHIER F, FOURNIER J P. Development of powder metallurgy impellers for vinci hydrogen turbopump: AIAA 2000-3831 [R]. USA: AIAA, 2000.
[6] OHTA T, KIMOTO K, KAWAI T, et al. Design, fabrication and test of the RL60 fuel turbopump: AIAA 2003-5073 [R]. USA: AIAA, 2003.
[7] GAYDA J, KANTZOS P. High temperature burst testing of a superalloy disks with a dual grain structure: NASA/TM-2004-212884 [R]. USA: NASA, 2004.
[8] JOHNSSON R, BRODIN S, EKEDAHL P, et al. Development of hydrogen and oxygen pump turbines for vinci engine: AIAA 2002-4331 [R]. USA: AIAA, 2002.
[9] 朱大鑫. 涡轮增压与涡轮增压器[M]. 北京: 机械工业出版社, 1992.
[10] 冯引利, 吴长波, 高鹏, 等. 某粉末冶金高温合金涡轮盘破裂转速分析[J]. 航空动力学报, 2013, 28(3): 501-506.
[11] 吴长波, 卿华, 冯引利, 等. 某高压涡轮整体叶盘破裂转速计算方法及试验验证[J]. 燃气涡轮试验与研究, 2006, 19(3): 33-36.
[12] 赵俊生, 马朝臣, 胡辽平. 车用涡轮增压器叶轮破裂转速的弹塑性数值分析[J]. 机械科学与技术, 2008, 27(1): 45-49.
[13] 张德禹, 黄金平, 黄道琼, 等. 离心泵叶轮爆裂转速数值仿真和试验[J]. 计算机辅助工程, 2013, 22(增刊1): 175-178.
[14] 刘璐璐, 宣海军, 洪伟荣. 某型涡轮盘破裂转速计算及试验验证[C]//中国航空学会第七届动力年会文集. 贵阳: 中国航空学会动力专业分会, 2010.
[15] GYEKENYESI J Z, MURTHY P L N, MITAL S K. NASLIFE-component fatigue and creep life prediction program: NASA/TM-2005-213886/REV2 [R]. USA: NASA, 2014.
[16] CEN. Unfired pressure vessel standard: EN 13445-3 [S]. Brussels: European Committee for Standardization, 2002.
[17] 陆君毅, 吴荣仁, 周储, 等. 转子失效分析的重要试验-转子超速破坏试验[J]. 机械工程材料, 1992, 16(6): 54-56.
[18] 窦唯, 金志磊, 闫宇龙. 液体火箭发动机涡轮转子超速离心变形特性研究[J]. 火箭推进, 2015, 41(5): 23-28.
DOU Wei, JIN Zhilei, YAN Yulong. Over-speed centrifugal deformation characteristics of turbine-rotor in liquid propellant rocket engine [J]. Journal ofrocket propulsion, 2015, 41(5): 23-28.

相似文献/References:

[1]郑 伟,李护林,陈新红.激光快速成形技术在液体动力领域的应用前景[J].火箭推进,2015,41(06):1.
　ZHENG Wei,LI Hulin,CHEN Xinhong.Application prospect of laser rapid prototyping technology in the field of liquid power[J].Journal of Rocket Propulsion,2015,41(05):1.
[2]郭 敬,宋晶晶,孔凡超.发动机推进剂增压输送系统建模仿真技术综述[J].火箭推进,2015,41(05):1.
　GUO Jing,SONG Jingjing,KONG Fanchao.Overview of modeling and simulation technology for propellant pressurization feed system of liquid rocket engine[J].Journal of Rocket Propulsion,2015,41(05):1.
[3]于 康,谢荣华,陈晓江.表面张力贮箱电子束焊接工艺研究[J].火箭推进,2015,41(05):89.
　YU Kang,XIE Ronghua,CHEN Xiaojiang.Study on electron beam welding process for surface tension tank[J].Journal of Rocket Propulsion,2015,41(05):89.
[4]刘中华,苏 晨,汪军安,等.气路膜片设计研究[J].火箭推进,2015,41(05):95.
　LIU Zhonghua,SU Chen,WANG Junan,et al.Design and study of pneumatic diaphragm in gas circuit[J].Journal of Rocket Propulsion,2015,41(05):95.
[5]薛 薇,蔡震宇,曹红娟,等.基于可视化平台的液氢/液氧火箭发动机核心部件质量计算[J].火箭推进,2015,41(04):61.
　XUE wei,CAI Zhenyu,CAO Hongjuan,et al.Mass calculation of key assembly units in LH2/ LOX rocket engine based on visual interface[J].Journal of Rocket Propulsion,2015,41(05):61.
[6]穆朋刚,童 飞,蒲光荣,等.温度对贮箱增压系统的影响分析[J].火箭推进,2015,41(04):74.
　MU Penggang,TONG Fei,PU Guangrong,et al.Influence of temperature on tank pressurization system[J].Journal of Rocket Propulsion,2015,41(05):74.
[7]高朝辉,刘 宇,肖 肖,等.垂直着陆重复使用运载火箭对动力技术的挑战[J].火箭推进,2015,41(03):1.
　GAO Zhao-hui,LIU Yu,et al.Challenge to propulsion technology for vertical landing reusable launch vehicle[J].Journal of Rocket Propulsion,2015,41(05):1.
[8]申智帅,等.气动增压器技术及其在空间推进系统的应用[J].火箭推进,2015,41(03):15.
　SHEN Zhi-shuai,RUAN Hai-jun,et al.Pneumopump technology and its application in space propulsion system[J].Journal of Rocket Propulsion,2015,41(05):15.
[9]张 翔,徐洪平,安雪岩,等.液体火箭发动机稳态运行故障 数据聚类分析研究0[J].火箭推进,2015,41(02):118.
　ZHANG Xiang,XU Hong-ping,AN Xue-yan,et al.Clustering analysis for fault data in steady process of liquid propellant rocket engine[J].Journal of Rocket Propulsion,2015,41(05):118.
[10]窦 唯,闫宇龙,金志磊,等.某发动机涡轮泵转子高温超速/疲劳试验研究[J].火箭推进,2015,41(01):15.
　DOU Wei,YAN Yu-long,JIN Zhi-lei,et al.Fatigue experiment of turbo-pump rotor at over-speed and high temperature condition[J].Journal of Rocket Propulsion,2015,41(05):15.

备注/Memo

收稿日期:2017-07-14; 修回日期:2017-09-01 基金项目:国家基础研究项目(613321) 作者简介: 王振(1984—),男,博士后,研究领域为液体火箭发动机结构安全评价技术

更新日期/Last Update: 2017-11-10